Is this fitted wrong?

Discussion in 'CB Range' started by Lockdown, Jan 11, 2015.

Top Posters
  1. Lockdown
    Offline

    Lockdown Long term member

    Joined:
    Oct 20, 2014
    Messages:
    187
    Likes Received:
    50
    Trophy Points:
    38
    Gender:
    Male
    Location: (Country, Region - and perhaps even City?):
    Worcestershire
    Local Time:
    5:54 AM
    #1 Lockdown, Jan 11, 2015
  2. Wendygirl
    Offline

    Wendygirl To offer advice and keep CM safe and welcoming

    Joined:
    Jul 31, 2013
    Messages:
    3,360
    Likes Received:
    2,462
    Trophy Points:
    153
    Gender:
    Female
    Occupation:
    gardener
    Location: (Country, Region - and perhaps even City?):
    London
    Local Time:
    5:54 AM
    #2 Wendygirl, Jan 11, 2015
    Not sure why you think it's wrong?

    However unless he has very big balls the gap is quite wide thus escape looks easy.
    . Xx Wendy
     
  3. Lockdown
    Offline

    Lockdown Long term member

    Joined:
    Oct 20, 2014
    Messages:
    187
    Likes Received:
    50
    Trophy Points:
    38
    Gender:
    Male
    Location: (Country, Region - and perhaps even City?):
    Worcestershire
    Local Time:
    5:54 AM
    #3 Lockdown, Jan 11, 2015
    I think it's wrong because the guide pin plate has been put through the front ( instead of being on the base ring)
     
    lockedUp24byKH likes this.
  4. C. Roc
    Offline

    C. Roc Active member

    Joined:
    Jan 10, 2015
    Messages:
    61
    Likes Received:
    34
    Trophy Points:
    28
    Gender:
    Male
    Local Time:
    5:54 AM
    #4 C. Roc, Jan 11, 2015
    Hello.

    Think you need to disassemble then start again. There should be no gap between the back ring around your balls and the cage, unless you plan to put a points of intrigue (the spikey things), if so fit it now so you have the spacing right.
    Fit the shortest rod with the hole at the end for the lock in the center hole, from your body pointing outwards.
    Then you will have the two white rods digging inwards into your body. You need to cut these down with a hacksaw blade. Have them protruding a bit so just in case you need to do some adjustments, find your balls too pinched, you still can do so. Once you have it on for a month or so (not in one go) but you are very sure everything is comfortable then cut back these two white rods to almost flush. Hope that as clear as mud.. good luck..
     
  5. reefknot
    Offline

    reefknot New member

    Joined:
    Apr 3, 2011
    Messages:
    9
    Likes Received:
    9
    Trophy Points:
    3
    Gender:
    Male
    Local Time:
    5:54 AM
    #5 reefknot, Jan 11, 2015
    Someone needs to rfm,
    I suppose it works but its not how its intended to be worn
     
    Lockdown likes this.
  6. Lockdown
    Offline

    Lockdown Long term member

    Joined:
    Oct 20, 2014
    Messages:
    187
    Likes Received:
    50
    Trophy Points:
    38
    Gender:
    Male
    Location: (Country, Region - and perhaps even City?):
    Worcestershire
    Local Time:
    5:54 AM
    #6 Lockdown, Jan 11, 2015
    I did think its not as instructed but thought , is there an advantage to this !
     
  7. lockedUp24byKH
    Offline

    lockedUp24byKH Yes Dear...Right away.

    Joined:
    Feb 7, 2014
    Messages:
    692
    Likes Received:
    428
    Trophy Points:
    73
    Gender:
    Male
    Location: (Country, Region - and perhaps even City?):
    Ireland
    Local Time:
    5:54 AM
    #7 lockedUp24byKH, Jan 11, 2015
    Lockdown you answered your on question.

    the guide pin plate has been put through the front ( instead of being on the base ring)

    Fitted wrong and the pins will break or the plastic connected to the pins will.
     
    Lockdown likes this.
  8. GT-CB6000
    Offline

    GT-CB6000 Long term member

    Joined:
    Sep 7, 2014
    Messages:
    354
    Likes Received:
    124
    Trophy Points:
    53
    Gender:
    Male
    Local Time:
    12:54 AM
    #8 GT-CB6000, Jan 11, 2015
    I can not see any advantages of wearing it that way. On second thought the guide pins will not protrude out of the front.Creating a smoother front. This can be resolved by trimming the guide pins shorter when you have found the correct fitting spacer setup. JMO
     
  9. reefknot
    Offline

    reefknot New member

    Joined:
    Apr 3, 2011
    Messages:
    9
    Likes Received:
    9
    Trophy Points:
    3
    Gender:
    Male
    Local Time:
    5:54 AM
    #9 reefknot, Jan 17, 2015
    The only advantage is it pushes the cock cage out by the thickness of that part of the ball ring but as others have said the pins are at risk of breaking.

    Someone did not read the f'ing manual
     
  10. guodor
    Offline

    guodor Chastity FAN!

    Joined:
    Oct 18, 2009
    Messages:
    104
    Likes Received:
    248
    Trophy Points:
    43
    Gender:
    Male
    Location: (Country, Region - and perhaps even City?):
    Portugal
    Local Time:
    5:54 AM
    #10 guodor, Apr 26, 2015
    in the CB-xxx website they have an animated 3d that shows how it is assembled.
    I never thought that anyone wouldn't get it straight ahead. For me it is so intuitive!
     
  11. filltee
    Offline

    filltee Junior Member

    Joined:
    May 21, 2010
    Messages:
    3,394
    Likes Received:
    2,512
    Trophy Points:
    143
    Gender:
    Male
    Location: (Country, Region - and perhaps even City?):
    Sheffield. South Yorkshire UK
    Local Time:
    5:54 AM
    #11 filltee, Apr 29, 2015
    If you don't know then you don't know at least he had the sense and the guts to ask for guidance
    His gf is pretty too. Though not much point in showing her face and not yours

    Anyway I hope this helps

    there are plenty more like it just google

    how to fit a cb6000 chastity device
     
(You must log in or sign up to post here.)
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice