Hi, all! ChastityTech is back! On the off chance you've heard of us, we first launched in 2021 and in the past couple years have worked extremely hard on a site overhaul and a brand new line of cages, the Model F. The new cage is backed up by some awesome software to let you see a rendering of your customized cage (which can even be viewed in augmented reality) before ordering. This aims to improve the customer experience of ordering a highly customized product and helps to remove some of the guesswork and uncertainty from the process. We are very excited to hear any and all feedback from the community, thanks! https://www.chastitytech.com/
While your chastity device looks interesting there is nowhere to input measurements. When you refer tothat and don't deliveron that what are we supposed to assume about the actual devices?
Hi, I'm not sure what you mean by nowhere to input measurements. Did you visit the product page? If you go to the Model F page and select the order tab you will see where to input measurements
May I offer some comments: At $150 USD, you’re at the low end of the custom made market, well more expensive than the off the shelf market, which is fair enough. For those with some experience in this, we are used to being able to quote measurements as ring diameter (not circumference), total cage length, cage diameter. It would be easier if you offered those dimensions in your website. We’re also very interested in what it’s made of when it’s not steel, and would like to know more about the plastic, how tough is it, will it bend, how smooth is it, some 3D offerings aren’t quite smooth and required some fine sanding to get them smoother for wear. I hope that’s helpful, good luck with the business!
Thanks so much taking a look and for the advice! With the pricing we did want to stay lower than most other custom devices, but are you saying this puts us in an undesirable "in between" spot in the market? The measurements were something we worked with volunteers a lot on and what we settled on was what we found the most success with. They are a little different than the norm as you pointed out but we are hoping the measurement guide is detailed enough to make up for it. But if people are struggling with it we will definitely keep your advice in mind! As for the material, it is a tough, rigid, biocompatible plastic called Nylon PA12. After being printed the device undergoes a process called vapor smoothing. This yields a smooth surface that while being a little more textured than your traditional injection molded plastics, is plenty smooth for comfortable wearing and definitely doesn't require sanding. Everything is ready to go out of the box. If you want more information we link to the material datasheet on our FAQ page. Thanks again for the advice!
Are you really using an SLS printer? That's a crazy expensive solution but gets the job done. I guess my suggestion would be that the pictures on the site look like renders and not the real prints. If I'm correct, I would suggest showing a few finished products in a model's hand so you demonstrate a real world product.
Your website indicates that you will generate a 3d image of the cage for us to see. Obviously I would expect it to be before the order process. That's a bit of a no brainer.
I’m sure you’ve done your market analysis on competitors — in the non steel market that I’m aware of you’re well positioned on price compared to Cherry Keeper and Holy Trainer, and cheaper than Custom Chastity, Evotion Wearables and Blackout. So I don’t think price is a barrier for you in the custom made sector, then it’s about quality, and getting awareness of your product out there. Regarding the gap, the critical measurement to resolve issues of the balls slipping through is the “diagonal gap”, which is explained really well on the Badass Workroom website, they’ve nailed a solution for that.
I don’t know if I missed something here, but I went to your website via the link to check out your new belt design and see pricing and how ordering was and frankly I could not find how or where you order one. The product page shows you a product but doesn’t bring you to a purchase point. The measurement page brings you to a guide but doesn’t redirect to a product….I don’t see how you are going to make any money if no one can buy a product from your website…did I miss something?
I had the same problem at first. At the top of the Model F product page, click the word "Order" to switch from the "About" tab to the "Order" tab.
Yes SLS printing is the best way to get safe, end-use products from 3D printing! You are correct everything on the site is currently a render. That is a good idea I will look at putting a gallery section up perhaps. Thanks!
From reading some of the comments below I think I may know what the issue is. If you go to the Model F page it loads the "About" section by default. If you click the "Order" tab it will load the page where you can render your cage before adding it to the cart. Since this seems to be causing some confusion I will look at perhaps having the "Order" tab be the default load.
Thanks! Obviously I believe we have an extremely high quality device so we are working on getting awareness out there at the moment. Yes the "gap" measurement we have on our site could also better be described as a diagonal gap. I will check out their explanation and see if I can work mine better. Thanks!
It sounds like this is an issue people are running into a lot. As someone posted below, the product page has two tabs, an "About" tab and an "Order" tab. The "About" tab loads by default and you have to click the "Order" button at the top of the page. I will probably have to change how this is oriented. This feedback is very helpful thank you!
How about you let potential customers go through the size stage before the dreaded word order comes to the fore. This is a word that deters a lot of people. The fact that your rices are reasonable is beside the point. We want to see how detailed the process is before looking to order something. If when we have designed the device we then see the price and can see a button to order it there we would not be put off. In fact we would be very tempted. Do I make my point. Order early is a taboo word.
Lol thank you for the visual. I will try and add real images to our site to avoid customers having this fear
oh, i'd suggest cylinder- like base rings, in addition to the a circular ring. the former are *so* mulch easier for long-term wear, at least in my case.
He's referring to the ergonomic type of base ring... like this: https://www.amazon.com/Jefisry-Closed-Stainless-Chasity-Virginity/dp/B09MKFZBMC?th=1
Product looks good and I found it easy to navigate. I will be keen to see some actual product photos and read reviews from customers when they start coming through.