How do i fix that i can pull out my dick out of the chastity?

Sorry - I mean that I bought a variety of 3D devices for about $30-50 each.

Will probably keep the old ones for variety, or find some local sub and lock them on his penis, just for my fun. Shame to see a cage not being used!

 

I totally agree! My 24/7 device is a custom 3D print, it’s the perfect fit.

 

The nice thing too is that many/most of the 3D printed devices are light, yet still *very* strong. So, for 24/7 they are ideal.

 

https://www.eroprofile.com/m/videos/view/Pierced-for-Lifelong-chastity

 

So, I posted this on the vice forum. I am dead between the two(see below). I have a vice mini v2. The 48 is very tight. Petroleum jelly makes it bearable and prevents chafing, but it can be tight. They suggested buying tubing to slip over the ring at the hardware store for the larger to prevent being able to slip out of the 57 and making a tighter fit. Has anyone done this? As for not pulling, even if I slip out of the larger ring, the anti pullout is very vice light and I can’t pullout of the tube.

• X-Large: 48.5 mm (1.90″)
• XX-Large: 57 mm (2.25″)

 

Is this PA placed back enough for chastity?

 

Best not to get hard then bro! ;-)

 

I guess I'm just lucky with my size and shape , but no way can I get out of my vice mini v2 when I attach the anti pullout.

 

Only way is a pa

 

Do you have any recommendations? I haven't seen a captive glans ring. Is that a second ring, inside the cage? Smaller I assume, to lock the head in place? Color me intrigued.

 

Weighing in to several posts with this one. Certainly Bondinchas speaks the truth, if you want *truly* inescapable lock-up.

Beyond those options:

1) Absolute smallest base ring possible. Work your way down to the smallest you can do; take your time.
2) Tubing can help to "adjust" between ring sizes with large differentials; you can add tubing until it doesn't "make sense" anymore, and by then you might be ready for that next smallest ring.
3) Do not underestimate the benefit of lube, lube, lube between the base ring and your body; the thing needs to be able to move in both directions as your change position, get a minor erection, etc. The better the ring can adjust as your body moves, the less discomfort there will be.

Using a combination of #1 and #3, I have been able to work my way down from a 1-3/4" base ring, comfortably to a 1-5/8", to a 1-1/2", though so far only for two+ days on that smallest one. (Consider: 1-1/2" is only a quarter-inch bigger than my cage inner diameter!) If my job was less physically active I could probably do the smallest one for three or so days. And that thing is so small there is no way I can pull the cage forward and down to pull out; heck, it's so small I can barely slip the jewels through! There was a time when I thought 1-1/2" would be impossible, but clearly it is not.

Try the tubing. It's cheap enough and *will* help. Eventually you may be able to make it down to the smallest ring, or, by some point, probably every plastic ring will be produce-able by someone with a 3D printer.

 

Have you tried reducing the distance between the base ring and the tube?

 

There is another option that works quite well.

You can buy silicon cock rings in different sizes. Usually the box of rings comes with plenty in different sizes. If a ring is found that sits firmly behind the glands (ie in the groove between glans and shaft), but is ideally just wider than the inside of the cage, then it can serve to hold the head of the penis at the end of the cage. The penis can (just) be pulled out out once the cage is off but takes a little pulling. It would make it very difficult to pull out while in the cage when locked with base ring. This probably only works where a penis has glans that are wider than the shaft.

So, you'd position the ring behind the glans, making sure the outside of the ring is a bit larger than the inside of the cage. Use a stocking to draw the penis (with ring) into the cage. Lock on the cage. Make sure the ring is at the widest part of cage. Enjoy not being able to pull out.

IMHO this is not necessary where the cage fits well (ie tight ring and long cage) but would work very well in most cases for making removal difficult.

 

You forgot a 5th method: a lockable waist band attached to the base ring.

 

I had the same question in my head, but it turned out it's irrelevant. At least for me. At least for now.
The thing is.. I do not forget it is my wish to be in chastity.
The only moment when I want to pull out and take care of myself is when I have attempted erection. But those are the moments when I actually can not pull out.
I can pull out only when flaccid. But when flaccid - I do not want to pull out.

Here I need to add a little disclaimer. I have not been locked for more than 6 weeks without orgasm. Maybe with longer periods I will get more desperate and will want to pull out when flaccid, but for now it is not an issue.

 

The sub drop stops me from pulling out and reliveing myself, I would be miserable for hours after. More security would be good psychologically tho

 

I don't know which country you are located in, but does Mature Metal ship there? They have the "sizing rings" kit, which IIRC had six or seven different sizes. Inexpensive, although NOT silicon, as recommended above.

 

If you’re that light a sleeper that you can’t even sleep in underwear, I can’t imagine why you would even consider sleeping in any chastity device.