Support belt/harness for ball trap devices

It rather depends on the device, however in the past when i had difficuty I placed a length of thin(ish) chain from one locking post / guide pin around my waste to the other post / pin.

This had the effect of pulling the cage in tight but pushing up.

To counteract this i placed a lenth of chain from the base ring (be careful how you attach here it can be a pinch point) through my ass cheeks and snugly attached to the belt chain with a small padlock.

This pulled the cage in tight and secure.

Ive often wondered if you could put tge cage through odildo harness to the have same effect.

 

I've been experimenting with it a bit with wire rope. It seemed ok at first but then I realised my cage sticks out a bit. Also, it moved so much that I could still pull out so might need some supporting straps going from the back of the harness to the front of the cage to pull it down and make more secure but I suspect I could still pull out. Either that or it would be too tight and I might hurt myself.

I'm trying to be careful though as the wire rope can cut into the skin and don't want loads of bits of this stuff on different parts of my cage as that's a slight hazard.

 

I used snaps and an elastic band to create my own. Took all of five minutes.
https://www.walmart.com/ip/Dritz-Snap-Fastener-Pliers/52765983
https://www.walmart.com/ip/Dritz-Snap-Fasteners-7-Count/120645270
https://www.walmart.com/ip/Dritz-1-Non-Roll-Black-Elastic-Value-Pack-5-Yd/294773420
I also am working on a "mounting" solution for typical steel Chinese devices
https://www.chastitymansion.com/forums/index.php?threads/waist-strap-helper.39361/#post-423174

 

I currently have a base ring that is a bit too big. However I find that wearing tight supportive underwear helps keep everything in place.

 

You can make a simple and comfortable waistband with paracord that will keep the cage closer to the body. I recommend using 100% nylon paracord (MIL-C-5040) instead of the cheaper polyester cord. The nylon dries quickly and doesn't get a mildew smell.

Securing the paracord with an adjustable knot will allow you to change the tension throughout the day, and for different activities (there is a pic in my gallery). For example you may prefer it tight for sleeping, looser to hang more naturally while in trousers, then the most loose to point down while using the toilet.

Good luck, and I hope you find a solution that works for you.

 

Aircraft Cable works well since it's vinyl coated and aluminum crimping sleeves to join or make loops for locks.

https://www.amazon.com/Forney-70452-Aircraft-250-Feet-16-Inch/dp/B003YDK49M/ref=sr_1_3


https://www.amazon.com/dp/B07QJ9FK9C/ref=sspa_dk_detail_3

 

I found a good pre-made and adjustable harness on Etsy. Arrived today and works really well to support a metal ring type cage.

https://www.etsy.com/listing/860446908/custom-chastity-support-band

 

That looks like such a good idea

 

I purchased one of these belts last year.

https://www.ebay.co.uk/itm/362537976615

I have adapted it slighly so it works with all my chastity devices but it's comfotabke and keeps tge ring close to body. Some photos on my galley.

 

Also started using a more conventional fix - https://www.jockey.com/catalog/product/jockey-mens-logo-y-front-trunk?color=0406
These briefs have a just-right pouch to hold/cup the ring/cage and support it. So I use the support belt when I want something more presentable and the briefs for when going out to be more sure that things won't move out of place.

 

So do you fit the cages back ring, then the harness ring and then lock it all in with the cage?