I’m about to buy my first device. After a lot of reading I’ve decide on the holy trainer. There are however some questions where I could use some feedback. First of all the ring size. I had the idea to buy an ordinary metal ring in 45mm and see how that feels when worn for a few days. If needed I can size up or down. Good approach? The cage size is the most difficult one. Not sure between the small and nano. I’ve read some negative things on the nano about the gap. The small one doesn’t seem to have that problem. Does the small one however still concealable? Any advice is greatly appreciated!
I think its really the ring size thats the thing you need to get rigt. cos it has to be just rigt and really the cage dont has to be very very rigt. it has to fit yes but it cud be a little bit big or a bit short. but if the rings not rigt it will fall off if it big and hurt if it to small. and a lot of men that get the first cage has the ring to big.
Hey there! You could try using an adjustable radiator hose clamp with a thin band.... That way you can adjust until you find an accurate fit. Then you can mark, remove and measure for accuracy....? My advice here is do not wear this at night to sleep in. If you have it too tight when you sleep you could be in some real discomfort...... Use it in the day and stimulate yourself so you can see how it feels when you're erect. You'll know if it's too tight cos it will cause you real discomfort.... Guidelines for base rings are that you should be able to get one finger underneath comfortably in your normal state.... I suggest this as it is an adjustable method. If the 45mm ring is not a good fit, what then? You may have to buy more.... That's time and money gone too.... As for cage size.... I don't have nor have ever used a HT.... You can measure yourself when flaccid a few times to get a good average. Don't let any male ego get in the way here! A cage that's too long will cause problems when you're erect (or trying to get that way!) Hopefully other HT users will give better advice here! I hope this helps! Good luck Kindest regards J. https://circled.com.au/foton-cooling-system/5371-radiator-hose-clamp.html
I would repeat advice I've have seen from a user several times, Buy a cheap knock off of the device, plenty of those online, use that for test drive to get the size right then buy the official product for longer term wear.
I’ve tried CB6000S and HTv3 standard and nano (knock offs) I had nothing but problems with both. The largest rings let me fall out and the ring below that size caused burning. I tried every lubrication and spacer combination. I read in here it’s better to have a steel device so I bough a cheap steel with three sized rings. Bingo, I’ve had no problems and manage to wear 24/7 whereas with the other plastic devices I couldn’t keep them in for more than an hour. Hope this is of help.
I'm about to start too. Have you purchased a device? How does it fit? How well does it work . Thanks for the help
Yes, I first purchased a knock off CB6000S it came with three base rings. I have high tight balls so the largest ring allowed my balls to slip through while the smaller caused burning on the under side of my scrotum. I then purchased a Holy Trainer standard knock off and I found the same problem. I also purchased a HT nano with the same issue. (I actually put a post on here about the problem as well as talking in the chat room). Many people said stainless steel was better so I purchase a cheap steel one with three rings and I fits. Other people swear by the HT but I guess my high balls caused an issue. Hope this helps.
Thank you all for the responses. Tip of the radiator hose clamp was a creative one, but personally I was a bit worried to have such a industrial piece on my body. In the meanwhile I’ve bought a metal cockring dia 45mm. It seems to fit all the bills. I can just squeeze a finger in between. Now I do read everywhere that you shouldn’t wear a cock ring for more the 20 to 30 minutes. On the other hand when it comes to chastity devices, I read suggestion to try out this size for a couple of days. Of course I want to keep it save. What’s the consensus here?
Ok, I followed the advice and bought a cheap knockoff of the cb6000s. After trying out the cockring, which seemed to be the correct size, I had a lot of trouble getting it off. the cb system is using open rings, so let’s experiment first with these. Thanks for all the suggestions!
I found the cb6000s comfy enough but it was quite pinchy to put on and my kh never quite got on with putting it on either. If you ave similair issues I would reccomend trying a Holy trainer.
Skip the plastic stuff. Go steel. Try a few inexpensive devices off aliexpress or amazon. A272 and A273 models are great designs.
Ok, just put on the cb6000s for a try. I barely seem to fit in with the largest ring and the largest spacer. I’m uncut and the excess skin is gathered just in front of the case. Perhaps I just have gone for the cb6000 instead? Don’t know if photos are allowed here so I uploaded it to the gallery.