Just as a matter of interest - what are the ring size for the CB6000 you mostly use. There is multiple choice if you vary the size. Probably like many, I only use two of the rings and have just had my "normal" ring break on me and have had to send for a new one, post haste! The support from Mr Miller in the US has been great - not so the retailer in the UK. Happy to sell me a new one - but slow to respond to my requests to replace the 3 month old broken one so far. No response to emails or messages when buying the replacement. (Update - vendor responds asking me to send broken bits to request replacement from States.) it might be an interesting piece of research - unless already done.
Dolly started with a 2" and progressed over the course of a year to a 1.75". What size ring do you need, carrie? dollyanne
So far i used the largest ring with the 2nd largest spacer, but today i finally managed to wear the 2nd largest one
Well Dollyanne, i use the smallest spacer but need the largest size ring and that is quite a squeeze - but last week i wore the next size down for a day and it felt like the blood supply was being cut off! Then when i was going back to the larger size the ring broke - so i am enduring ring 2 until the postman delivers tomorrow hopefully! Interesting that you have managed to downsize over a period of time - well done!
I use the 2nd largest ring with the 2nd smallest spacer. working out where during the course of my day can go from +40'c to as low as -6'c, i need the room to allow my balls to move otherwise i get imense pain.
I just moved down to the second smallest ring today. When I started with the largest ring about 3 weeks ago, it was so wide, I could barely get my legs close enough together to have my feet on the clutch and brake at the same time while driving. I have been steadily working my way down to smaller rings just to make things more comfortable and keep the rings from pressing into the sides of my legs.
I'm doing the #4. The #3 pinches under my balls when I get wood. Pinching is an urgent pain for me. I can deal with most of the other.
I use the largest ring and largest spacer. Madam finds it amusing to watch me try to get the device on. It's always at least a half hour of fiddling with lube and the judicious use of q-tips and careful positioning to get the ring on. A slightly larger one would probably work better. Big balls, small dick.
Currently I'm trying to get used to my first device. Tried #2 and it felt snug but a bit too tight so I'm on the largest
I use the largest, which feels a bit too snug but I'm sure I'll adapt. It's wearable. (I have gigantic nuts...)
I use ring 3 but can't believe it's 45mm - that size in other devices I've used have been too big. Don't mind me, just replying to a ten-year-old thread
I wanna know who uses the number 5, and do you use it with the shortest spacer? I use the number 1 with the shortest spacer.
Ring N. 1 and I am progressively reducing the gap between tube and ring with the spacers. My anatomy doe not allow me to use smaller ring, actually my size would be 55/55 mm
I find the smaller ring size I need the bigger spacer for gap if I use the 2 inch then it goes with no spacer. I have the cb600s and with no spacer cock goes right to the end so most times its the 1-7/8 and small space works best for me
Started with ring number 5 and the largest space but as I go more use to wear ring 3 and the 2nd smallest spacer. Have tried a number of times with ring #4 which is fine for a few hours but then seems to cause an issue.
I might be wrong but I prefer to use the spacer(s) on the outside of the locking pin, so I am able to push and lock the tube toward the base ring. When I insert the cage I always push the cockhead to the end of the tube to align the peehole to the opening of the tube and I add one or more spacers to reach a comfortable squeeze. I wear the CB6000S cage and when I am flaccid I am slightly longer and wider than the tube so I have to squeeze everything in. I am presently increasing the length of the spacers to reduce the gap and to obtain a firm but safe confinement and a mostly internal hard on when excited https://www.chastitymansion.com/forums/index.php?gallery/photos/squeezing.65806/
my ring is not on there cos Mistress got it maked for me. i did have a cb6000s first ages ago but the small ring was still to big for me. and the cage was as well.