For those of u who have the funnel tube, does it protrude past the outer cage? I wear a 2 inch tube, so I assume it would be two inches then go into the taper with protruding a little past the cage? Tired of the hygiene issues.
I have 2 funnel tubes and 1 does extend past the outer cage opening, is an issue if I sit on a hard surface. The other ends about 1/2 inch above the outer cage opening and I use a small silicone funnel to bridge the gap. I have a new funnel on order to meet sit flush with the cage opening and ideally that will be "just right"
That would be ideal. Control and no wetness. May I ask your Order number for that tube? Sounds perfect, I want a 2 inch tube with funnel. Does the funeral squeeze the penis when u try to get erect? I no the Neosteel has a design that’s close
Hi -the funnel tubes are 100% custom orders so you can specify what you would like. If you provide a picture with measurements to BB, they're pretty good about making it happen. in terms of the NS funnel/squeeze shape, that is possible, just have to draw/list out what you want to BB and they can confirm if it is doable. Note- they are also taking orders for the new hybrid tube with dual over the butt wires if you don't like the single rod. This also makes the tube extra secure to where you could omit the outer cage at times; mine is on order can let you know how it turns out in a few weeks.
Hey can you please show us pictures of your custom funnel? I'm curious for the looks. I have also a 2"device and have the same problems
Sure -you can see the 2 types in the attached pic, I do prefer the lower one with a solid/closed lower funnel piece. The upper one can leak a bit if you aren't lined up 100% correctly. The middle item is a rear rod anchor ring combo as I have a removable outer cage and didn't want to lose the "anchor" via the rod.
I will say 1 more thing, I am getting a 3rd funnel tube that extends to be flush with the outer cage lower opening. This is a case of too much/too little -the upper tube funnel extends 1 inch too long and hits on hard surfaces when sitting and the lower one is about 1 inch short so I bridge the gap with a silicone funnel. Lesson I learned is it needs to be just right else you won't totally solve the problem.
Hey, How is the Rod/Ring combo for everyday use ? What are your balls doing with that extra bit of metal down there changing/reducing the space in the outer cage ?
It works pretty well, the longer, smooth piece at the bottom sits below the balls and doesn't irritate anything, cage bottom sits on top of it to an extent so no real reduction in space. Having a more closed cage helps prevent ball sac spread/pinching
Heh looks very close to the one I have on order! Including the retainer for the dual over the butt cables. Matt-Locked - the funnel helps keep my balls pushed in/organized so the sac doesn't spread out all over. Also BB accommodated a last min request to reshape the bottom of the external cage to have a round opening for the spout versus the larger standard oval. Also helps to reduce sac skin pinching.
If you did the design work, THANK YOU. I have the tube extending a few mm past the outer cage. Cannot wait until I get it!!!
@ Chaste Nole: I am curious about the rear rod anchor ring combo. This would, I believe, increase comfort in my case, as it would allow for a larger, looser ring, while holding it snug to the body and preventing pullout. Is that custom made, or did it come from BB?
Austin- it was a custom order from BB - I also am trying a new cock ring/tube based wire design to prevent pullout and w/o using the metal rod. The first pic (disassembled) is what I have and the second is from BB (posted here earlier) of the style assembled. So far it is pretty good, just that the tubing gets stuck on the skin a but and pulls...
How was the comfort/security with the ring that had the rod attached? I had to do some bending of the rings & tube in a vice to make them fit more flush against my body, did you need to do the same? If so was it more difficult with the rod attachment?
It was very secure -no possible way to pull up enough to make space to pull out. And yes, I also had to use a vise to bend it a bit and cut the rod too (too long) so that it fit well without too much rod sticking up at the waistband. Comfort was 7/10, the BB cock rings invariably put a bit too much pressure when I am sitting and it gets uncomfortable after a few hrs.
I'd rather have the tube extend a little beyond the cage: That is nothing that careful application of a Dremel can't fix. Wear your safety glasses!
Hi! Have you already received it? Would you also have a picture on how it looks like when it is assembled? I mean does the funnel really go through the outer tube and how far? Thanks for your help as I am looking for a very similiar modification... Cheers, Dani
Sorry no pics. Yes the tube clears the outer cage by 1/8 of an inch or so. I can imagine going back to the normal tube. The cable upgrade is also very much worth the money!