Testicle Retraction

Sorry to say but i think the only solution is a better cage.
The CB series where trail blazers but not very good.

In the meantime move to a smaller base ring and tighten the gap,

 

Either ring or gap between ring and the cage is too big.

 

I would recommend a Holy Trainer cage as the next step, you can get knock-offs for under $20 on ebay. Resin and plastic cages usually come with multiple rings so you can experiment to find the one that works best for you. When deciding on which cage size to buy, it's best to size down rather than up, even if that seems counter-intuitive. If you have any room to grow in your cage, nocturnal erections will be harder to deal with.

https://www.ebay.com/itm/353581105451

 

my ones go back in me all the time if my cage is not on. but they cant when it on cos the ring stops them. your ring must be not tihgt .

 

I had this problem. the solution for me was to get a PA piercing and a shaft cage held on by the piercing.

 

If you were to go with a belt style chastity cage you would completely eliminate your problem.

 

Ok, he’s just getting started, piercings and full belts, that might be too much too soon. I’d follow the advice to ditch the CB6000, try some cheapies from eBay, Amazon, DH Gate, either in plastic or steel (open designs are better for easy hygiene).

The base ring size and the gap between it and the cage piece will determine if yours balls slip out or not. There’s no shortcut here, some trial and error will be needed.

 

Go smaller on the ring

 

go for a device with a curved ring base solved my problem so the ring sits closer and tighter to your pelvis and yes make sure the gap is smaller and go for a smaller cage,

 

Cos my cages stop my cock growing outwards my erections (when i get them) now go inwards, but my balls remain in place

 

I would try a stainless steel Nub or a cap device. There is no room for anything to move, they are comfortable, and can be purchased from DH Gate for a reasonable price. The steel models are heavier so I use a waist belt to relieve the weight and to make the device very secure.

 

Please be aware of the knock offs. They are made using petroleum. Something that my body just didn't like. There's also a strong smell of petroleum.

 

A chastity device with a hinged ring will let you get a much smaller grip than the regular rings that you have to squeeze all your "parts" through.
I have always had frequent testicle retraction so I know how you feel, and the difficulty that makes for chastity. Here is an inexpensive one, if the point it closes pinches you can get or make a plastic "sleeve" to slide over that area.
Good luck !

https://www.amazon.com/TERNENCE-Sta...7150a&pd_rd_wg=VVrDi&pd_rd_i=B07HGSTM8Q&psc=1

 

I recommend the Cherry Keeper as a good way of getting a good fit as extra rings or cages are inexpensive. However, for some, retracting balls means that ball trap devices are just not suitable.

 

It is so reassuring to read that others have this problem. It is very frustrating to be secured only to later have one ball pop, then the other and the cage fall off *blush* Soooo embarrassing!!!
The other cages mentioned will be investigated, but i was reminded by an online Mistress that the best chastity tool is the mind.

 

The difference with a "hinged ring" device is that although they are ball-trap they do not have to be big enough to push the balls through, instead the ring opens and then can be closed to a smaller circumference, a tighter ring that makes it less possible for even one testicle to pass through it.

 

well my little ones go inside me but only when i am not in my cage. they cant do it then cos the ring wont let them.

 

Could I ask what cage you use? Although I can bear the ball trap, I have always been intrigued by using my PA to tether something and have it more "connected" to me. Even harder to find steel/metal solutions for uncut dudes. I've thought many times about circumcision but my KH loves it and it's sensitivity when she decides to play with it... Lot of people recommend Evotion and I've made some tentative enquiries there, but is an expensive road to travel :/

 

I agree that it might b too much in a short time, but I think it is not a bad Idea to put those options here as I consider the Piercing with an shaft only evice as the most comfortable solution in his case. Going for a smaller gap might be the second best solution, but might still give problems. Apart from that - if you go for too small a gap you might get problems with the bloodflow....

 

I'm just starting out and have 4 cheap cages, none of them work well. The one that is the best is made from cheap plastic that flexes after wearing it for a while. This allows the ring gap to spread and my testicles pop out. It seems to me at this point, the most important dimension to keeping it on is that ring gap, which most cheap cages don't address. With them you need to go to a smaller ring to reduce the ring gap, which just doesn't work for me. So until I spend enough to get a custom cage I doubt I will find a cage that is comfortable and stays on properly. I will probably go custom, and right now I'm looking at Evotion plastic cages and Badassworkroom metal cages.

 

Hi Tarknassus, I have an Evotion Bijou, very comfortable. If you get one, make sure you have it fairly tight on your shaft, that keeps it from slipping down onto your piercing and dont get it too long otherwise when you sit it will again push down onto your piercing.

 

Is there a reason why you didn't get the orion? From the looks of it, I would think you could wear it with or without the base ring.

 

I didnt really think about it. I knew I didnt want a ball trap device so went for Bijou, apart from it being a bit cheaper! But also my sack is generally so tight that a base ring has nowhere to grip.

 

As others posters have said, you need to reduce your ring size and your cage to ring gap, you maybe surprised just how samples you need it.