The largest ring they offer is too tight!

Discussion in 'HolyTrainer' started by SeeMeFeelMe, Oct 23, 2017.

  1. SeeMeFeelMe
    Offline

    Joined:
    Oct 23, 2017
    Messages:
    6
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    Occupation:
    Attorney
    Location: (Country, Region - and perhaps even City?):
    California
    Local Time:
    5:13 AM
    What should I do?

    Should I try sanding down the one I have? Should I try to come up with an alternate way to affix the tube?

    Help!

    Thanks,
    SMFM
     
  2. Mistress B
    Offline

    Mistress B Mistress B

    Joined:
    Feb 29, 2012
    Messages:
    2,451
    Likes Received:
    3,504
    Trophy Points:
    153
    Gender:
    Female
    Occupation:
    Business Owner
    Location: (Country, Region - and perhaps even City?):
    United Kingdom
    Local Time:
    12:13 PM
    Sand it down ???? Is it wooden ??
     
  3. SeeMeFeelMe
    Offline

    Joined:
    Oct 23, 2017
    Messages:
    6
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    Occupation:
    Attorney
    Location: (Country, Region - and perhaps even City?):
    California
    Local Time:
    5:13 AM
    No it's plastic :O! Idk, I'm just trying to find a solution hahah
     
  4. Mistress B
    Offline

    Mistress B Mistress B

    Joined:
    Feb 29, 2012
    Messages:
    2,451
    Likes Received:
    3,504
    Trophy Points:
    153
    Gender:
    Female
    Occupation:
    Business Owner
    Location: (Country, Region - and perhaps even City?):
    United Kingdom
    Local Time:
    12:13 PM
    The largest rings I have seen on sale have been 52mm, do your need larger than that ??
     
  5. SeeMeFeelMe
    Offline

    Joined:
    Oct 23, 2017
    Messages:
    6
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    Occupation:
    Attorney
    Location: (Country, Region - and perhaps even City?):
    California
    Local Time:
    5:13 AM
    I think so?? My balls get cold and tuck themselves away and when that happens it really hurts! When it's nice and warm then there are no issues haha
     
  6. Lakeman
    Offline

    Lakeman Long term member

    Joined:
    Mar 5, 2017
    Messages:
    905
    Likes Received:
    917
    Trophy Points:
    103
    Gender:
    Male
    Location: (Country, Region - and perhaps even City?):
    Australia
    Local Time:
    11:13 PM
    The CB series make rings in 2 and 1/8 inches and 2 and 1/4 inches, the bigger of which is around 57mm. Other than that, I think you’ll need to go custom made.
     
  7. Nicoftime
    Offline

    Nicoftime The suspense is terrible...I hope it lasts

    Joined:
    May 24, 2016
    Messages:
    5,233
    Likes Received:
    14,083
    Trophy Points:
    143
    Gender:
    Male
    Occupation:
    Railroad
    Location: (Country, Region - and perhaps even City?):
    South of Lacrosse Wisconsin
    Home Page:
    Local Time:
    7:13 AM
    Devices are not comfy. If the temp is causing them to retract and hurt and it’s fine when warm...stay warm.

    Your boys do a lot of moving, all day and all night. They are meant to, and it’s going to cause some discomfort. Same with erections. Attempting them will hurt. It causthe cage to pull away from your body and sliding your ring down the sack and squeezing your balls. This happens. What you don’t want is the ring to stay there. So keep it lubed so when your excitement ends, the ring slides back into place, same goes for the cold.
     
  8. sandman9355
    Offline

    sandman9355 Junior Member

    Joined:
    Oct 10, 2008
    Messages:
    347
    Likes Received:
    347
    Trophy Points:
    63
    Local Time:
    1:13 PM
    I know the pain, literally. The ring I need is more like 62mm, not 52mm. However, the only solutions I've been able to find are either custom parts, or DIY. The DIY route can be both low-tech (a file) or high-tech (3D printing), and expect to make a few mistakes before you find a solution that works for you. However, it is still likely to be cheaper than undergoing the trial-and-error process using custom parts.
     
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice