So this might be a silly question but with devices like the Steelworxx Looker 02 they appear to have a one piece 'a-ring', how are you meant to get that on? I ask because until this point we have just been using CB6K devices where the a-ring is assembled in place and other devices where the ring is folds into place and is then secured closed. Had a go earlier at trying to get through the CB6K a-ring when it was in one piece by trying to put a testicle through at a time but it didn't seem like it would work very easily. Any tips for the best way to get on a one piece a-ring?
I get one ball through then keep pulling skin through, just concentrate on getting as much loose skin through as possible. The other ball will either pop in itself of go in quite easily. Once both balls are through work on getting your penis in.
It’s one ball at a time. Pull some skin through then push ball through. Pull more skin through then the other ball, then push your member through at the top. If really having issues, lube with baby oil gel (works great for me), and use toilet paper as gloves to be able to grip the slickness of the ball sack.
I have problems with the solid ring in that I’ll get one through and the other goes into hiding. So I have to keep a good hold on both as I’m putting them through. Makes it a bit tricky but practice makes perfect.
also try to get your sack as loose as possible. if I'm uncaged and take a shower I usually need to wait a bit for the temperature to increase that my balls hang a bit lower.
I use the balls first, then member method. I have found that using a cock ring behind my balls helps to keep them from escaping. Once everything is in place, stretch the ring and remove. I just don't get to use this method much anymore...
I agree with all the suggestions on here. As a side comment I have found two piece a rings or ones with a hinge made a spot on the ring that had rough edges and made this less comfortable in long run even with surgical tubing covering the break in the ring. It is worth the extra hassle of putting on a one piece and after you get used to it, not so bad to put on.
I had a device with a hinged ring, not a plesant experiance, pinching down under. An oval solid ring is to my opinion the best, as descript by others put your testicles through , and use the soch method for your penis. Smal panty hose over your penis, top of the hose throu the ring and pull the penis throuh. Sorry for my bad englisch
once you have both balls through the ring, there are two ways to get your penis through - some find one way much easier than the other. In both cases, pulling the bottom of the ring up against the body and the scrotum down helps get skin in the right place for pushing it through. a) push the head through first, then a combination of pulling head and/or pushing with thumbs from behind. Once you're halfway there it'll just pop through. b) push base through first, head last. You'll likely prefer one method over the other, it depends on which way you bend!
Thanks all for the advice, I tried it and worked well! Last time I tried it straight after a shower which I think did not help and wasn't sure about the best technique.
BTW - It's not necessary to remove the base ring to masturbate (if you have permission.) So you can get a fairly tight base ring and only have to go through this process very rarely. Hope this helps
Something that works reasonably well for me is getting the balls through and most of the scrotum, then slipping in the head and using the scrotum like a little carpet to pull the rest through. I usually have to take my PA out too, that way I don't tug on it.
Many thanks for this thread. I too have had problems and a bit of pain, but the effort is worth it. I now put a tight leather ligature around my balls to prevent them disappearing into my body (heaven knows where they go), then I insert the penis and then balls one at a time. Will certainly try the 'penis last' process next time, it should make the balls easier and less painful. Don't forget to release and remove the ligature at the end, otherwise blue ball syndrome.
Well, what a revelation. Fitted the 45 ring today following suggestions in this thread. Ligature around whole package to stop 'pocketing the pinks'. Then balls, one at a time through the ring. Easier than before and certainly less bruising. Then removed the ligature. Then forced the flaccid snake through the ring. Once his head was through he seemed quite content to slither in afterwards. Also tried some lube to prevent the pinching when package tightens - that works. Found a small square of face flannel which I placed around 'bulb' of the device and secured with a rubber band. Now the steady stream of fluid from the urethral insert is absorbed before it soils my panties. As the excitement dies down after a few hours? days? weeks? you can confidently dispense with flannel.