Hello I have tried about 4 to 5 different chastity caged. The problem is that the tube of the case is too narrow. Are there cages for men who have a thicker, but not longer penis? Thanks for answering, Subcuir
I don't know if there is a cheaper cage you can get to solve your issue here. Others will have to chime in. I do hope you don't have to go custom :0 Do you know what was the largest size you could find was?
You’d be best to divulge the diameter you’ve tried, or what you think would fit you. Trying devices you buy for $25 a pop is common now, but actually measuring yourself works better. After 4-5 disappointments the costs start to add up! Most of what’s on the mass-made market are 1-1/4” to 1-3/8” (32-35 mm) internal diameter cages. I felt constricted in my CB6k and Holy Trainer. I’d turtle up too because they were too long. I ended up going with an open style cage, custom-made by MaleChastityNow. Later I found I could fit in a tighter open style cage than I could a closed tube. Now I’m in a smaller diameter cage than I was in 2014. The cage is just 1/8” narrower but it makes a big difference. A light touch vs feeling held, not squeezed, when flaccid and at rest. Getting shaft / glans rings to test fit helps. There’s a URL in the following fitting advice page that shows where you can get rings for $2 each, or less if you buy one of the sets. http://malechastitynow.com/measuring.html Good luck.
The Cherry Keeper lineup offers quite a few "wide" cages which take the standard 35mm diameter cage and up it to 45mmx35mm. Lengthwise, there's a Short (51mm), a Small (61mm), and a long (76mm) as well as a number of customs of various diameters and lengths http://www.cherrykeeper.com/ I'd be happy to help you with any questions as it's my shop
How do you define "too narrow"? Are you not able to get in? If so, I recommend the "stocking method." It works very well for me, and I can get into a cage that fits snugly when I am not erect, which I find preferable to a cage that has excess room in it.
That's not going to work for everyone - I can "stocking method" into a standard size cage, but as things move and shift, always wind up only halfway in because the cage is too narrow. Getting in can be solved, but having a proper diameter/width cage truly makes for a better experience in my book
Nothing works for everyone. But many people don't understand how to get into a properly sized cage, and because of that buy one that is too large, leaving too much extra space. If you use the stocking method properly but still can't get into the cage, then it's too narrow. Generally speaking, if you can get into it with the stocking method and fill it comfortably when flaccid, it's not too narrow.
Your disagreement is noted, but not understood. What does “too narrow” mean to you? If you can get into it, what is too narrow about it? What exactly happens that you don’t like? You mentioned things shifting around, which I don’t get, because in a snug cage, things shift less than in a roomy one.
Take a Holy Trainer for instance - standard tube diameter is 1.4" ~35mm, but is too long. Going with a short the diameter is down to 1.2" or 30mm. I can stocking into the short HT and have to really work to pull the nylon out because my head is ~50mmx35mm at the absolute back edge (I forget shaft width, but it's 40mm+). I can be fully seated at the tip at the start, but as I move and my body shifts (i.e. bend over at the waist), the head will pull back just a bit, but can't go back down because it's 50% larger than the space it's trying to occupy, and you can pull a string, but can't push one. That will happen repeatedly, miniscule amounts at a time, and I'll never be seated at the tip again in that cage. You can say that it's because the cage is too long, and I thought that was the problem as well, so I did a bunch of shorter models of the cage, and no matter how short I went, I had the same issue (The nub is a different story). All the HT tube models I've posted here and on thingiverse were an effort to solve this problem before I realized the root of the problem with the width, not the length. For comparison, the same thing happens with the one metal device I own, even though the length matches my length. Fast forward to today, in a Cherry Keeper Wide that's 45x35, I wear one that's ~68mm deep, or even the 51mm short-wide, and never have issues. It may just be that it's the HT style (and metal capped style) that causes the issue, but the other issue I'm concerned about with a narrower cage would be it causing edemas on the shaft by being too narrow.
For me a cage is too narrow, like JosieLynn already said, when the penis can't slide back in completely after some slipping occurred. And slipping is kinda inevitable, even if you wear a tight full belt. It will slip a little bit, if you bend over. I found, that cage were most comfortable to wear, when the inner circumference matched the circumference of the flacid shaft.
How wide is yours when flacid? That might help for suggesting something. My latest cage has an inner diameter of 40 mm and i found it on amazon.de Most cheap cages i found have an inner diameter of 30 mm to 38 mm. 40 mm was a rare exception. Above 40 mm it's hard to find a cheap massproduced device imho.
Cd Erica, could I please get a link to that cage you got off amazon, if it’s not to much trouble. Thank you.
Just been looking at your site and find your devices very attractive, I’m looking for a cage that is the same dimensions at the old xb2000, do you have any plans to do something similar to cbs points of intrigue? As I am still in a cb 2000 with the points and my madam does like them. Thanks for your time.
I don't have formal plans to add something like that to the Cherry Keeper, but I have experimented with them on a concept I was working on a few month ago. I see a way I could add this to the current design, it would just be a bit of time as there are three or four things in the design queue I want to make available soon (two are 95-99% done!)
Thanks for your fast reply! Cannot wait to see what will be available soon! Will be going through your site tonight with my madam and see if she will accept losing the points. Also took a look at your photos, and that black no fun cage is fascinating, does it screw on to the base ring? Thanks again for your reply, x
https://www.amazon.de/gp/product/B01IXZG7HS/ Sadly it's no longer available. But maybe you can find something similar.
The cage goes over the pins sticking out, and the screws stop the cage from being pulled off. It came with little pop in plastic pieces that did the same thing, but I added the screws instead. That one is actually not my design, it was my "gateway" cage into chastity, and can be found on Thingiverse.
What you describe I feel is exactly the failure with my mancage #6. The base and midshaft catch enough that upper shaft foreskin never rests at the right place far (deep enough) in the cage to fit properly. I thought I sized it too long, despite measuring several times before picking that device. You just gave me vital insight. Thank you.