Mature Metal Jailbird - getting the right size

Discussion in 'Chastity and orgasm denial' started by Guest 1793, May 8, 2017.

Random Thread
  1. Guest 1793
    Offline

    Guest 1793 Member

    Joined:
    Mar 15, 2017
    Messages:
    10
    Likes Received:
    2
    Trophy Points:
    3
    Local Time:
    10:22 PM
    Hope you can help.

    Having got the sizing wrong first time round on a Jailbird - hoping to get it right this time!

    I have the sizing rings which hopefully will help...

    In terms of the cock ring internal diameter:

    1.75 (which I bought first time) I can get more than the tip of one finger in...
    1 5/8 seems snug - perfect?
    but with a little bit of a squeeze I can get into the 1.5...

    should I think of a custom 1 1/6?

    The cage internal diameter:

    1.25 or 1 1/8, the latter is a snug fit on my shaft but my glans measurement is more like 1.25, is this measurement key - is it best to go tighter?

    Length - I am about 6 hard and 3 soft - there seems to be a consensus that going smaller is better but how short?

    Hoping to get the dimensions right.

    Many thanks,

    simon
     
  2. Vinny
    Offline

    Vinny Locked up again. Starting year 6.

    Joined:
    Jul 24, 2014
    Messages:
    1,879
    Likes Received:
    1,668
    Trophy Points:
    143
    Local Time:
    6:22 PM
    I too had to send it back. I wore a 1.75mm ring on my off the shelf devices but I got the oval ring for the Jailbird and it would fall off. I went to the 1.5mm ring and it was very tight at first but now I am used to it and it is extremely comfortable and have worn it for about 4 years 24/7. They can even make one in-between sizes or any size you want. If you think 1.5 is too tight, split the difference. It is funny how 1/8th of an inch can make a difference. They can resize you ring instead of making a new one. I think it cost me $20 4 years ago plus postage to get it to them. Turn around time was under 2 weeks. What I did was have them resize my ring to 1.5mm and also make me a new one in-between the two.

    Do not know if you got the security screw or not. If you did, it will back out over time. It was very tight at first but loosed up after a few months. You can ask them to sink the screw when you send it back so that more surface area of the screw head will contact the round ring. What I do is either use Teflon tape which is used to create a tight fit on water pipes or LokTite Blue. Only the blue stuff that comes in a red tube. If you get Loktite RED in some other color tube, it can only be removed using an industrial strength hot air gun that will burn you badly. The blue Loktite works very well. What it does is get into the screw groves and harden. To unscrew the screw you need to use a little more force than you normally do which is more than you can do by hand. Just in case I bought a screw extractor which is like a pair of pliers but will grip the edges of a screw head tightly and allow me to break the seal of the LokTite. I have not had to use it since the key will break the bond with some force applied.
     
    manintyres likes this.
  3. Guest 1793
    Offline

    Guest 1793 Member

    Joined:
    Mar 15, 2017
    Messages:
    10
    Likes Received:
    2
    Trophy Points:
    3
    Local Time:
    10:22 PM
    Vinny,

    Many thanks for the reply - I think I will go for the 1 5/8 and a you say I can always get a 1.5 at some point further down the track.

    In terms of the internal diameter and length of the cage - what are your thoughts on these measurements? Along time back I had a CB2000 and I remember getting blisters on my penis from the pressure my erections created - but as I get older I dont get such strong erections and use viagra when having "moments" with my better half. I am quite envious of your partners will to minimise your orgams!
     
  4. Wife's Submissive
    Offline

    Wife's Submissive Loving being denied by wife!

    Joined:
    Nov 27, 2016
    Messages:
    66
    Likes Received:
    14
    Trophy Points:
    8
    Gender:
    Male
    Location: (Country, Region - and perhaps even City?):
    USA
    Local Time:
    6:22 PM
    I would recommend not being small on the diameter. I did that and now have a cage I can't comfortably get into and have stopped wearing. If 1.25 is your glans measurement then I wouldn't go smaller than that or else you will have to struggle to get it on. And also if it shrinks up(which it will) then it won't be able to push back up the cage. I would prefer it not be tight on diameter.

    Length seems to be a bigger factor then being too wide in my opinion. Keep in mind the smaller it is the more comfortable it will be. However the shorter you make it the wider it would need to be. I would think 2.5 inches if you are 3inches flaccid. But check the diameter with it being pushed in to that length as you might see you want to go wider than 1.25. Diameter can't be changed after the fact.

    Would highly recommend contacting mature metal as well as they know best.
     
  5. PouchPantyLover
    Offline

    PouchPantyLover Long term member

    Joined:
    Mar 6, 2017
    Messages:
    1,203
    Likes Received:
    2,258
    Trophy Points:
    133
    Gender:
    Male
    Location: (Country, Region - and perhaps even City?):
    Hawaii
    Local Time:
    12:22 PM
    I'm actually getting my jailbird resized now and I found Mature Metal to be very professional, quick to respond and will make any adjustments they can for nominal cost. What they don't seem to like to do is make specific recommendations. They will not tell you what size to choose. Probably had people complain about being given bad advice, but it does make it hard to decide. I agree with @Wife's Submissive on width. Before sending my jailbird back MM had me send a pic and they said diameter was too narrow. Problem is when I'm taking it off or putting it on I am not at my smallest size and it can bind up in that process. Too narrow will be a problem.

    I am getting my ring and my gap both enlarged by 1/8 and it was $15 for each, so those adjustments are minor. Diameter can't be changed, what you buy is what you live with. Length is where I really messed up. I am getting it shortened by a full 3/4" and that is costing $100. I think it's really hard to measure yourself without some arousal, but I had no idea I was that far off. After wearing it for awhile MM had me put q-tip in the end and measure how far the q-tip went in. Was a real eye opener. Whatever your smallest measurement is of yourself, shave another 1/4" or more off that in my opinion.
     
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice