Hi everyone, Does anyone have problem with the connection bending inward? It rubs my skin so much and gives a horrible burning sensation. It wakes me up at nights and it is even more horrible when I sit at my desk at work as it hurts a lot! I basically can’t wear the cage because of that. Does anyone have a solution? Best Regards Londonpup
Same belt, same problem. I've been toying with the idea of getting a second outer cage that doesn't have the rod attachment, but it's a lot of $$. I find that the cage and rod combo is fine during the day when I'm up and active but quickly becomes unbearable when sitting down or lying in bed. I'd be interested to know how you resolve this
hi interested to know exactly which part of the bend is rubbing and against which part of you? the cage used to have the curve turned the opposite way so pointing down rather than in, but a few customers mentioned it pressed against their clothing more in that style. I dont seem to have the issues you mention but i can accept that it is an issue for you, it would be easily possible for you to actually use a strong pair of pointed nosed pliers and actually rebend the curve so it pointed downwards and see if that helped. it would be helpful if you could explain more about where and how its rubbing?........any chance of a close up with the belt in position and being worn?
i dont know if you are a member on fetlife but if you are have a look on my pictures on there as you can see on mine the bend you show is dressed down further on mine at the front edge and maybe that is what you need to do to yours a little so it does not catch on the edge. The barrel nut has to slide in from the side on mine to fit to the rod as it cannot slip under the open end as it is bent downwards to much.
It's not rubbing as much as it just puts too much pressure on my perenium. My cage sounds similar to yours in its construction and how it's rolled, but it's still just a little much I guess. I'm tall, thin and short waisted, which has been a challenge since I started with chastity. I also tend to wear my belt fairly snug as I'm constantly bending and lifting things, and the looser it is the more it tends to pinch!
is it the bend that is putting the pressure on your perenium or could it possibly be the actual angle of the ned in the rod itself ? i know Joe put a bend in my rod for me and i found that a little too much but the strength in the actual rod itself once bent takes a hell of a lot of effort to try and straighten the bend out even by a small amount. If you had met Joe you would have seen just how big and strong he is and the way he bends some of the metal objects with his bare hands is a sight to see in itself. Have a check to see whether it is the bend on the rod that is putting the pressure on. As for the posters picture showing the curved mounting point it should be much more closed than it is and the open edge wrapped right down tight around the locating barrel nut which would take it away from where it could catch and rub.
I have the same problem. I just ordered another belt and asked them to bend that piece in the opposite direction so that it will be tucked up under the cage. Which they said they would do.
I also heated my Hannibal 1 cage and bent it in the opposite direction. I can send pictures when I get home.
It's definitely the cage; I have the same issue when wearing just the outer cage without the rod. I'll try to steal a moment tomorrow to look more closely at the cage and see if I can adjust the attachment point. I was struck by the attachment style shown earlier in this thread and may give that a go as well.
I hate this cage. This is the worst one I have ever got. The company was helpful before deliver but doesn’t reply to any email anymore right after delivery.
I had this issue. Bend the outer cage away just a little. I use the rear bar as it is the most secure and does not have that gap. I also wrap it in a water proof tape that softens the metal against the perineum area. I can wear the belt weeks at a time with these modifications. With out, I can't
We are sorry if you have experienced any slow replies, given the current Pandemic we are in and out the office and working from home the best we can, Drop us another email and ill see to it that this gets solved for you, like others have stated above, bending the hook the other way is an option but we can discuss it further over email, Thank you