Looking for measuring/comfort tips for base rings maybe rigid model 5

Discussion in 'Novices and newbies' started by JackKneels, Nov 5, 2018.

Tags:
Top Posters
  1. JackKneels
    Offline

    JackKneels New member

    Joined:
    Aug 2, 2011
    Messages:
    7
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    Location: (Country, Region - and perhaps even City?):
    USA, NYC
    Local Time:
    1:07 AM
    #1 JackKneels, Nov 5, 2018
    Hello, I am thinking of buying a rigid chastity model 5. I am larger then average but not pornstar huge.

    1) *Base ring...Is it better to have it snug, or as wide as possible for long term wear? I feel like if you can sneak balls through ring, You can pull out? Hard to know whats comfortable vs security? a

    2) I get the basics of measuring cage length, but if it is a little snug, or a little bigger is this an issue? No prince Albert. like when you try and grow...the tip of the cage? I had a jail bird, i think, that had a sharp weld at the tip, when I'd get fully erect it would sometimes scratch me... got rid of it.

    3) interior diameter: The site recommends using the girth erect...But I am curved up, while cage is curved down and the cage is recommended to be shorter, so I can't imagine ever getting fully hard in cage?

    4) interior diameter : I have a bon4L...which was skin tight (Diameter) on my flaccid penis. Didn't allow any air in or out..which caused chaffing and moisture to always be there...

    I am thinking of a getting it big enough to have air with flaccid, but just a smidge under my full erection. To much space can allow pull out?

    I am eager to have a quality device.
    I also considered the Pet Trap from mature metal.

    any other custom devices I should look at?
     
  2. jb123
    Offline

    jb123 Long term member

    Joined:
    Mar 21, 2018
    Messages:
    394
    Likes Received:
    355
    Trophy Points:
    73
    Gender:
    Male
    Occupation:
    Analyst
    Location: (Country, Region - and perhaps even City?):
    USA
    Local Time:
    1:07 AM
    #2 jb123, Nov 6, 2018
    Just be aware, Rigid will take up to four months to arrive.

    I fudged the measurements when I ordered my RC #1. I ended up going with a MaleChastitynow Contender with a PA hook. It undoubtedly the most comfortable device I have ever worn. Plus, the turn around time was ONE WEEK!!!!!!!!!
     
    Peter Rabbit likes this.
  3. JackKneels
    Offline

    JackKneels New member

    Joined:
    Aug 2, 2011
    Messages:
    7
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    Location: (Country, Region - and perhaps even City?):
    USA, NYC
    Local Time:
    1:07 AM
    #3 JackKneels, Nov 8, 2018
    thanks for the info, i will check it out. Although, I do not have a PA piercing ....4 months, I'm in no real rush, lol...enjoying the freedom!
     
  4. Nicoftime
    Offline

    Nicoftime The suspense is terrible...I hope it lasts

    Joined:
    May 24, 2016
    Messages:
    5,252
    Likes Received:
    14,143
    Trophy Points:
    143
    Gender:
    Male
    Occupation:
    Railroad
    Location: (Country, Region - and perhaps even City?):
    South of Lacrosse Wisconsin
    Home Page:
    Local Time:
    12:07 AM
    #4 Nicoftime, Nov 8, 2018
    Might want to check if that model is offered without pa...I don’t think it is. They do make one without but it’s not the 05.

    If no pa to worry about I would stick with cage length of flaccid measuring from point of contact on balls under penis to tip.

    Diameter go with a tad wider than you when flaccid.

    Base ring go with not being able to stick more than your finger up to the knuckle in from the top. Normally this could be a bit larger because it’s anchored by your piercing, but you aren’t getting that one.

    Good luck
     
    lexie likes this.
  5. Adam444
    Offline

    Adam444 Long term member

    Joined:
    Oct 14, 2018
    Messages:
    540
    Likes Received:
    500
    Trophy Points:
    73
    Gender:
    Male
    Location: (Country, Region - and perhaps even City?):
    Chicagoland, USA
    Local Time:
    1:07 AM
    #5 Adam444, Nov 9, 2018
    The tube should be about the size of your flaccid penis. That doesn't slightly aroused or after taking the Polar Bear Plunge. I saw something where the guy layed it out on a table and measured, several times. The idea being that a correctly sized tube will curb (not eliminate) an erection so it will be more comfortable. An erection pushes the tube away from your body, taking the base ring and your testicles with it. The other alternative is a tube the size of your erect penis, but that generally isn't practical.

    Base ring should be snug but loose enough that you can get the tip of your finger between it and your body. It should not be so small as to cause swelling, skin cooling, or skin discoloration.
     
    JackKneels likes this.
  6. JackKneels
    Offline

    JackKneels New member

    Joined:
    Aug 2, 2011
    Messages:
    7
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    Location: (Country, Region - and perhaps even City?):
    USA, NYC
    Local Time:
    1:07 AM
    #6 JackKneels, Nov 10, 2018
    There is an option under hook type for "no PA hook"...I know of someone who has this exact model, without the PA. His wife runs a tumblr that often feature him with the model 5.
     
  7. Nicoftime
    Offline

    Nicoftime The suspense is terrible...I hope it lasts

    Joined:
    May 24, 2016
    Messages:
    5,252
    Likes Received:
    14,143
    Trophy Points:
    143
    Gender:
    Male
    Occupation:
    Railroad
    Location: (Country, Region - and perhaps even City?):
    South of Lacrosse Wisconsin
    Home Page:
    Local Time:
    12:07 AM
    #7 Nicoftime, Nov 10, 2018
    Cool, I do know they make another model as well without. Good luck
     
(You must log in or sign up to post here.)
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice